Jobs Board Electricians Jobs in Kedron Electricians Jobs in Kedron

Install 3 purchased led bunker lights. Switch and conduit outlets in place. Install 3 purchased led bunker lights. Switch and conduit outlets in place.

Need 5 downlights installed Need 5 downlights installed

We need a newly installed air conditioner connected in a granny flat. Electrical work needed only. Electrical box inside granny flat. Replace ceiling fan We need a newly installed air conditioner connected in a granny flat. Electrical work needed only. Electrical box inside granny flat. Replace ceiling fan

install 2 exterior security cameras install exterior power points for water feature install 2 exterior security cameras install exterior power points for water feature

2 story weatherboard house demolished.. I'm giving my aircond/electricals to some worthy people.. 2 story weatherboard house demolished.. I'm giving my aircond/electricals to some worthy people..

Ceiling fan in one room is extremely noisy and keeps knocking. Light in ceiling fan in another room keeps blowing as soon as it gets turned on. Ceiling fan in one room is extremely noisy and keeps knocking. Light in ceiling fan in another room keeps blowing as soon as it gets turned on.

We have 6 internal light fittings that need replacing. 4 existing ceiling pendants to be replaced by pendants and 2 ceiling mounted - one bring replaced by pendant and the other replaced by new... We have 6 internal light fittings that need replacing. 4 existing ceiling pendants to be replaced by pendants and 2 ceiling mounted - one bring replaced by pendant and the other replaced by new ceiling mounted. Looking for approximate quote. Wanting job completed in around 10 days when we collect the final two lights.

House RCD was tripping. Went through individual circuits – meggaring until found a fault on the Garage Circuit. Worked my way through garage looking for fault. Found fault to be at junction box... House RCD was tripping. Went through individual circuits – meggaring until found a fault on the Garage Circuit. Worked my way through garage looking for fault. Found fault to be at junction box before underground steel conduit that is under the house. Disconnected that cable, re-meggared and proved the fault was definitely that cable. Removed power circuit which was looped in with the garage circuit inside the house. Isolated the garage circuit at switchboard and also tagged off the cable that runs through the underground conduit so that it cant be reconnected.     KITCHEN • Removed single GPO off wall and replaced with Dbl GPO and mounting block • Measured and cut holes for new gpos on wall as to kitchen plan from ikea. Holes cut were for Range hood, Microwave and another GPO above bench. • Used yellow tongue to run 2.5mm cable between all the new GPO cutouts. Cable was free of charge. • Once cabinets were put in the holes weren’t in the right position. Due to an “extra cell” on the drawings, given by Ikea, the measurements were a lil out. Readjusted holes and moved cable to suit. • C-clips were used for GPO holes. All GPO`s were terminated and mounted to wall. • Light switch was replaced . • Hole cut out for GPO under sink for dishwasher. • Existing GPO on this wall taken off. Used yellow tongue to run between holes. 2.5mm Cable then run between the 2 holes. 2 new GPO`s then terminated and fixed to the wall in their corresponding places. 2.5mm Cable was free of charge. • All GPOs tested • GPO polarity tested • Kitchen power circuit meggared DINING • Existing Light switch removed and replaced with new Lightswitch • GPO for fridge removed. Tested circuit and there was no power present. Circuit that was in the wall was on the Garage Circuit. Isolated and made safe circuit. Went under the house and found an existing power circuit. Turned off circuit, tested and proved it was the power circuit I needed. Re-tested to prove it wasn’t live. Made cut and tapped into existing power circuit. BP`d and placed into joins into the junction box. Clipped Cable under house with clips 300mm apart to its location under the house. Used spade bit to make hole below where the new GPO is going. Used torch and yellow tongue to feed up through the hole, up the inside of wall, to where the GPO hole is. Ran cable up the inside of wall. Crawled out from under the house and went upto Dining. Put a mounting block on wall and terminated a double GPO. • Tested Circuit • Tested GPO and levels • Tested GPO polarity • Removed existing light and replaced with halogen light bar. Used wall mates in ceiling as there was no support in ceiling. Found a beam to screw one screw into – making the light fitting firm and secure. • Made sure light was square with walls. • Earth present – proven by earth continuity test from switchboard. LOUNGEROOM • Removed existing light and replaced with halogen light bar. Used wall mates in ceiling as there was no support in ceiling. Found a beam to screw one screw into – making the light fitting firm and secure. • Removed existing GPO • Went under the house and located where the current GPO is and where the client wanted the new GPO`s. Used spade bit to cut holes under where the new GPO`s and Antenna Cable are to go. • Ran new 2.5mm cable from existing GPO down to under the house. 2.5mm Cable was free of charge. • Clipped cable 300 mm apart to new GPO location. • Used yellow tongue to feed cable up wall. • Back into loungeroom to terminate and c-clip 2 GPO`s on wall for TV. • Removed existing Coax from wall. • Pulled back to under the house. Made a new join, then ran main coax into a splitter. From splitter the coax was clipped under the house 300mm apart to where client wanted new coax point. • Used yellow tongue to feed cable up wall. • Terminated coax to new faceplate and attached to wall. • Existing lightswitch removed and replaced with new one. • Made sure light was was square with walls. • All GPOs tested and levelled • GPO polarity tested • Circuits meggared • Earth present at light fitting – proven by earth continuity test from switchboard. SUNROOM/FRONTROOM • 2 new GPO`s wanted in sunroom for office area. Holes cut in location where client wanted them. Cuts were chiselled and broken out as wall was thought to contain asbestos. • Went under house and tried drilling through beam. Beam was too big to cut a hole through. Phoned client to see if a small hole could be made in the floor, hard up against the wall. Got confirmation and cut hole. • Turned power off to power circuits and found one to be tapped into. Re-tested to prove cable wasn’t live. Made cut and BP`d new 2.5mm cable off this. Used A junction box to put BP`d joins into. 2.5mm cable was free of charge. • Cable was pinned to beam under the house to new GPO locations, pinned 300mm apart. • Cable fed up to inside house. • Small hole cut at the base of the wall under GPO locations. Chiselled and broke small hole as wall contains Asbestos. • Yellow tongue fed from GPO holes to small hole at bottom of wall. • Cable pulled up inside of wall. • 2 GPOs terminated side by side with C-clips. • GPOs tested and levelled • GPO polarity tested • Circuit meggared • White Aussie duct was mitred and cut to size for exposed cable at base of wall. • Duct fitted • Hole to under the house was sealed with silicone FRONT BEDROOM • Existing light removed • New light holder fitted and bulb inserted • Existing light switch removed • New light switch terminated and fitted with C-clip • Existing GPO removed and replaced with new GPO • Hole cut in opposite wall for new GPO • Turned power circuit off • Tested that power circuit wasn’t live. • Went into bedroom 2 and removed GPO off wall. Fed yellow tongue from this GPO into new GPO hole, cut in Front Bedroom and attached 2.5mm cable. Went back into front bedroom and pulled new cable into the front bedroom. Terminated and C-clipped GPO in new position. Then went back into Bedroom 2 and replaced old GPO with new one. Terminated and fixed GPO back onto wall. • GPO tested • GPO polarity tested • Circuit meggared • Earth continuity test proven from light fitting to switchboard. Second Bedroom • GPO removed and replaced as explained in front bedroom. • GPO tested and levelled • Existing light removed • New Light bought by client fitted. Extra support and care was taken for this light as it is quite fragile. • Earth continuity test proven from light to switchboard. BATHROOM • Existing light removed • New light holder fitted and bulb inserted • Earth continuity test proven from light fitting to switchboard. • Power turned off and circuit tested to prove circuit wasn’t live. • Removed existing GPO. • Cut new hole through acrylic tile beside existing GPO for a new GPO beside existing one. • Terminated GPO and replaced existing GPO with a new one. This was terminated as well then both GPOs C-clipped and mounted to wall. • GPOs tested and levelled • GPO polarity tested Third Bedroom • Existing light removed • New light holder fitted and bulb inserted • Earth continuity test proven from light fitting to switchboard. FRONT OF HOUSE • Existing light removed • New halogen light fitted • Extra care had to be taken as surface contains asbestos • Earth continuity test proven from light fitting to switchboard. • Work completed at height BACK OF HOUSE • New lighting circuit ran from switchboard. • Conduited circuit with multiple bends, corro and saddles etc. to light switch on mounting block then out and up wall to under the awning. 2 holes were made 300mm apart. Chiselled holes as surface contains asbestos. Cable run between the 2 holes. Was time consuming as there is no access in roof. Sensor was fitted and terminated at one hole, flood light was fitted and terminated at other hole. • Earth continuity test proven from light fitting

Lowset! Could you quote replacement of a) replace 2x halogen (twin) bulb flood sensors for new.. b) Install 1x outdoor double outlet weatherproof Lowset! Could you quote replacement of a) replace 2x halogen (twin) bulb flood sensors for new.. b) Install 1x outdoor double outlet weatherproof

Been told old wiring not safe. Lighting circuit mainly. Been told old wiring not safe. Lighting circuit mainly.

We have some exisiting phone sockets that are currently not connected to our phone service and we would like them to be reconnected or to have a new one put in - we would like this to be done on... We have some exisiting phone sockets that are currently not connected to our phone service and we would like them to be reconnected or to have a new one put in - we would like this to be done on Monday 5th July. We would also like to have a quote for a data cable installed between 2 rooms- possibly to be done same day

I need an electrician to fix fault wiring in a fan with lights. Lights keep blowing when turned on. Can only be at home late afternoon or on Saturday I need an electrician to fix fault wiring in a fan with lights. Lights keep blowing when turned on. Can only be at home late afternoon or on Saturday

I need an additional telephone outlet in my study installed. I also have one telephone outlet upstairs that is not working. I have checked the line and the downstairs phone outlet is working, but... I need an additional telephone outlet in my study installed. I also have one telephone outlet upstairs that is not working. I have checked the line and the downstairs phone outlet is working, but the upstairs outlet is not working. I just moved into the property so am not sure what the fault is.

Need points fixed and system checked Need points fixed and system checked

Ariston LS620A dishwasher is pumping water in & out ok but not doing a wash cycle at all. Had not been used for approx six months prior to attempt over the weekend. Ariston LS620A dishwasher is pumping water in & out ok but not doing a wash cycle at all. Had not been used for approx six months prior to attempt over the weekend.

Electric range hood charisma brand fan no longer working Electric range hood charisma brand fan no longer working

replace ceiling fan and move light replace ceiling fan and move light

Find underground power cables, wanting to move benches/sheds close to the oval want to move cables b4 excavation work Find underground power cables, wanting to move benches/sheds close to the oval want to move cables b4 excavation work

security light installed & 2 power points installed,and replace porch light, cust will supply materials,double story,easy access. security light installed & 2 power points installed,and replace porch light, cust will supply materials,double story,easy access.

Due to my hours of work it would need to be after hours or on a saturday. Due to my hours of work it would need to be after hours or on a saturday.

electrician, need to remove two old lights, install 2 ceiling fans, install 4 down lights and change 2 light switches over electrician, need to remove two old lights, install 2 ceiling fans, install 4 down lights and change 2 light switches over

Disconnect power points Disconnect power points

tv points installed in 1 lounge,12 bedrooms tv points installed in 1 lounge,12 bedrooms

mains that come down into the box, take a look mains that come down into the box, take a look

Remove a fan/light and install chandelier, remove bayonet light and install bathroon light/heater/fan combo. Remove a fan/light and install chandelier, remove bayonet light and install bathroon light/heater/fan combo.

SAFETY SWITCH KEEPS TRIPPING - NEEDS SOMEONE TODAY ASAP SAFETY SWITCH KEEPS TRIPPING - NEEDS SOMEONE TODAY ASAP

PUT IN 2 DOUBLE POWER POINT AND PHONE LINE IN - - OZ TELE ELECTRICIANS PUT IN 2 DOUBLE POWER POINT AND PHONE LINE IN - - OZ TELE ELECTRICIANS